|
Restoration In case you need your artworks restored. |
|
Опции темы | Опции просмотра |
15.08.2009, 19:03 | Язык оригинала: Русский #1 |
Местный
|
Painting on metal, offering advice
Fragment of painting "Last Supper" done on zinc butter in a side light. Most likely this is a piece of the iconostasis. Across the surface of strong deformation on the mechanical effects of a sharp object on the reverse side. Paint in these places was preserved. I need advice as to align the deformation without damaging the paint layer. If someone faced with the - help, I will be grateful))))
|
15.08.2009, 21:08 | Язык оригинала: Русский #2 |
Banned
Регистрация: 25.07.2009
Адрес: Россия, Москва
Сообщений: 875
Спасибо: 1,092
Поблагодарили 1,380 раз(а) в 500 сообщениях
Записей в дневнике: 12
Репутация: 2190
|
From the perspective of an expert on construction
1) It is impossible to bend sheet metal back, if not exert pressure on the opposite side. If you knock on the front side - just corrupt the paint.
2) Or, drilled small holes in the steel wire that passes and try to pull the bulge back. The wire is attached with the front side with a steel ball or do loop, which pass through a very brief piece of steel wire. If you pull a solid, relatively thick wire (1 mm), then bends her end of the L-shaped 2-3 mm. Or use the corresponding L-shaped tool. Is that clear? This method provides no guarantees of full alignment, will necessarily uneven, but the smaller size. In the process of extraction can be damaged paint a diameter of several mm. from the hole. Hole-mask will restore. 3) I have carefully removed fragmented paint layer. Then he would calmly arched sheet and stuck a piece back. Question: Judging by the photo, work has already been decimated. If it will be fully restarirovat, redraw - the loss of even one small piece is almost invisible. Is there any historical value of the sheet metal? It may be easier to draw a new picture, and leave it as a sample? |
15.08.2009, 21:25 | Язык оригинала: Русский #3 |
Гуру
Регистрация: 23.07.2009
Сообщений: 5,736
Спасибо: 8,058
Поблагодарили 4,382 раз(а) в 2,259 сообщениях
Записей в дневнике: 2
Репутация: 8507
|
I would not be touched at all. (Easier to make a new zinc)
|
Этот пользователь сказал Спасибо NATA NOVA за это полезное сообщение: | Черномашенцев Владимир (15.08.2009) |
15.08.2009, 22:24 | Язык оригинала: Русский #5 |
Гуру
Регистрация: 23.07.2009
Сообщений: 5,736
Спасибо: 8,058
Поблагодарили 4,382 раз(а) в 2,259 сообщениях
Записей в дневнике: 2
Репутация: 8507
|
Chito vie mean? Once I was on a metal tray (stainless) palette divorced-so-so withered that so far I can not peel (you can give me the recipe?)
|
15.08.2009, 22:27 | Язык оригинала: Русский #6 |
Banned
Регистрация: 25.07.2009
Адрес: Россия, Москва
Сообщений: 875
Спасибо: 1,092
Поблагодарили 1,380 раз(а) в 500 сообщениях
Записей в дневнике: 12
Репутация: 2190
|
It's one of the "laws of the sandwich. I myself came up with:
"Cement has a habit easy to keep up with surfaces that are long and carefully prepared for work. But kept tightly wherever accidentally sprayed." That's about the paint from your tray can be paraphrased. |
16.08.2009, 06:24 | Язык оригинала: Русский #7 |
Гуру
Регистрация: 04.06.2008
Адрес: Сочи
Сообщений: 14,663
Спасибо: 18,865
Поблагодарили 16,455 раз(а) в 4,506 сообщениях
Записей в дневнике: 273
Репутация: 32442
|
Professional restorers are like no, but a serious question.
NATA NOVA, Chernomashentsev Vladimir,-people are very far from the Restoration (listen to their advice does not make sense). -------------------------------------------------- --------------- You better go to a specialized site (where collected restorers), there is a forum where you can ask a question. Site dedicated to the art of restoration and everything connected with it. http://www.art-con.ru/ |
Этот пользователь сказал Спасибо Евгений за это полезное сообщение: | Марина13 (23.08.2009) |
16.08.2009, 21:53 | Язык оригинала: Русский #9 |
Banned
Регистрация: 25.07.2009
Адрес: Россия, Москва
Сообщений: 875
Спасибо: 1,092
Поблагодарили 1,380 раз(а) в 500 сообщениях
Записей в дневнике: 12
Репутация: 2190
|
I agree with this statement. I have this and entered in the title of your post. For me you can pay attention only with regard to the alignment of the sheet of iron - as I understand it, this is the main problem. Judging by the questions posed.
|
17.08.2009, 08:09 | Язык оригинала: Русский #10 |
Гуру
Регистрация: 04.06.2008
Адрес: Сочи
Сообщений: 14,663
Спасибо: 18,865
Поблагодарили 16,455 раз(а) в 4,506 сообщениях
Записей в дневнике: 273
Репутация: 32442
|
The main problem is to keep painting ..
|
Этот пользователь сказал Спасибо Евгений за это полезное сообщение: | Марина13 (23.08.2009) |
|
|
Похожие темы | ||||
Тема | Автор | Разделы | Ответов | Последние сообщения |
American Painting | Pavel | Contemporary Art all over the world | 338 | 09.10.2012 14:53 |
Help Board | Сталевар | Import / Export | 6 | 14.09.2009 22:51 |
Here we have this painting | eva777 | Art Kaleidoscope | 8 | 15.07.2009 22:44 |
Help rate, European Painting | Lina | Costs, valuation, attribution | 11 | 18.06.2009 13:46 |
Painting Designs | LCR | Contemporary Art all over the world | 1 | 13.07.2008 12:01 |